1. The free wheeling mechanism contains
2. For each crankshaft revolution, the cam shaft revolves
3. The overdrive is located between______.
4. The synchronizing device used in the transmission uses
5. The second movement of the gear shift lever produces
6. There are two separate movements of the gear shift lever for changing the gears.The first movement selects
7. The standard transmission has
8. The conventional motor car has
9. In the transmission, the reverse idler gear always mesh with
10. In transmission reduction of speed is always used to obtain
11. The device that produces different gear ratios in the power train is called
12. In the automobile, the power train carries the engine power from the engine to the rear wheels. The power train includes the clutch propeller shaft, differential and
13. In the coil spring type of clutch when the pressure plate and cover are separated, the spring pressure must be held by
14. Parts of the clutch that should not be cleaned in solvent include the
15. On diaphragm spring clutch, pressing down on the clutch pedal moves throw out bearing in against the
16. As a general rule in facings on the friction disc are worn down to the rivet heads
17. The front end of the clutch shaft is supported in a pilot bearing in the
18. The three forward speed and the reverse transmission consists of three shafts and
19. Synchromesh devices in the transmission synchronize the gears about to be
20. In the transmission the counter shaft drive gear is meshed with a gear on the
21. The fluid coupling is most efficient as drive ratio approaching to
22. In the fluid coupling speed reduction means
23. When the clutch is engaged, spring pressure clamps the friction disc between the pressure plate and the
24. The free travel of the medal, or pedal lash is the amount of travel the pedal has before the throw out bearing comes up against the
25. The automobile transmission is removed from the car by taking it out
26. Overdrive is provided in the transmission of a vehicle to
27. The number of gear ratios in a vehicle
28. In the process of gear shifting in a layshaft type of gearbox
29. A fluid coupling
30. The main advantage of a fluid coupling is
31. The hydrodynamic torque converter
32. An automatic transmission works on the principle of
33. The coil springs are located in between the pressure plate and the
34. The clutch cover is bolted to the
35. The friction disc is positioned between the flywheel and the
36. There is a double faced friction disc splined to a shaft in the
37. To prevent distortion on re-installation on the clutch cover attaching bolts should be tightened
38. The power train transmits power from the engine to the
39. The clutch pressure plate is mounted on the
40. The release levers in a typical clutch pivot on
41. If two meshing gears have 4:1 gear ratio and the smaller gear has 12 teeth, the large gear will have
42. The two meshed gears have a gear ratio of 3:1. Every time the larger gear turns once the small gear will be to turn
43. In the diaphragm clutch inward movement of the throw out bearing causes the diaphragm spring to
44. The fluid coupling has maximum efficiency when driving and driven members are turning at
45. The purpose of the guide ring in the fluid coupling is to reduce oil
46. Synchronizing is designed to prevent gear clash when shifting into
47. When shifting into low, a gear on the transmission main shaft is moved in to mesh with the
48. Clutch noises are usually most noticeable when the engine is
49. Clashing of gears when shifting into high could result from
50. Transmission noise in neutral could result from
2. For each crankshaft revolution, the cam shaft revolves
3. The overdrive is located between______.
4. The synchronizing device used in the transmission uses
5. The second movement of the gear shift lever produces
6. There are two separate movements of the gear shift lever for changing the gears.The first movement selects
7. The standard transmission has
8. The conventional motor car has
9. In the transmission, the reverse idler gear always mesh with
10. In transmission reduction of speed is always used to obtain
11. The device that produces different gear ratios in the power train is called
12. In the automobile, the power train carries the engine power from the engine to the rear wheels. The power train includes the clutch propeller shaft, differential and
13. In the coil spring type of clutch when the pressure plate and cover are separated, the spring pressure must be held by
14. Parts of the clutch that should not be cleaned in solvent include the
15. On diaphragm spring clutch, pressing down on the clutch pedal moves throw out bearing in against the
16. As a general rule in facings on the friction disc are worn down to the rivet heads
17. The front end of the clutch shaft is supported in a pilot bearing in the
18. The three forward speed and the reverse transmission consists of three shafts and
19. Synchromesh devices in the transmission synchronize the gears about to be
20. In the transmission the counter shaft drive gear is meshed with a gear on the
21. The fluid coupling is most efficient as drive ratio approaching to
22. In the fluid coupling speed reduction means
23. When the clutch is engaged, spring pressure clamps the friction disc between the pressure plate and the
24. The free travel of the medal, or pedal lash is the amount of travel the pedal has before the throw out bearing comes up against the
25. The automobile transmission is removed from the car by taking it out
26. Overdrive is provided in the transmission of a vehicle to
27. The number of gear ratios in a vehicle
28. In the process of gear shifting in a layshaft type of gearbox
29. A fluid coupling
30. The main advantage of a fluid coupling is
31. The hydrodynamic torque converter
32. An automatic transmission works on the principle of
33. The coil springs are located in between the pressure plate and the
34. The clutch cover is bolted to the
35. The friction disc is positioned between the flywheel and the
36. There is a double faced friction disc splined to a shaft in the
37. To prevent distortion on re-installation on the clutch cover attaching bolts should be tightened
38. The power train transmits power from the engine to the
39. The clutch pressure plate is mounted on the
40. The release levers in a typical clutch pivot on
41. If two meshing gears have 4:1 gear ratio and the smaller gear has 12 teeth, the large gear will have
42. The two meshed gears have a gear ratio of 3:1. Every time the larger gear turns once the small gear will be to turn
43. In the diaphragm clutch inward movement of the throw out bearing causes the diaphragm spring to
44. The fluid coupling has maximum efficiency when driving and driven members are turning at
45. The purpose of the guide ring in the fluid coupling is to reduce oil
46. Synchronizing is designed to prevent gear clash when shifting into
47. When shifting into low, a gear on the transmission main shaft is moved in to mesh with the
48. Clutch noises are usually most noticeable when the engine is
49. Clashing of gears when shifting into high could result from
50. Transmission noise in neutral could result from
No comments:
Post a Comment